Home >

Abnormal Phenomena In Textile Machinery Market

2012/2/21 11:46:00 48

??? 日本語 Fran?ais English 中文

Textile Machinery Market Cotton Spinning Industry

Spare parts and equipment are shoddy.

Although significant progress has been made in the digestion and absorption and innovation of imported equipment,

Textile machinery

With the rapid development, there is also a situation of competing to lower prices.

For some high-end equipment and equipment, to ensure the performance and requirements of the equipment, it is necessary to purchase accessories, equipment and electronic components according to the international purchasing standard.

But what I see is that part of the textile machinery factory caters for it.

Spin

The factory pursues the so-called "good quality and low price", regardless of the strict standard of high-end equipment, and configures some shoddy spare parts and equipment.

I saw with my own eyes that the cots and aprons equipped with long spinning spindles (with automatic doffing) could not be used in only 4 months.

In the previous two years, a factory's high quality carding machine was still equipped with ordinary curved rail material.

The gap of tin Lin cover can not be guaranteed, while the track produced by the same product, TL tschille, is adjusted according to the FEM analysis method, and the 6 point gap is adjusted by using the gradual change of the track inclination.

Therefore, it is hoped that the machinery factory and the cotton mill should further coordinate and communicate with each other and avoid the unreasonable practices of the low-grade components or equipment in the high-end equipment configuration.

In addition, we can check that there are a large number of bearings abroad in the market.

trademark

Become the so-called imported parts of foreign packaging.

An engineer in a factory has developed a set of ability to identify false bearings.

In addition, close cooperation with factories, such as burn out motor repair, many repair shops without qualification, the motor around the motor does not guarantee the use period, often burned again in one or two months, without any testing means, only by so-called experience.

There is suspicion of exaggerating the function of the equipment.

In some textile machinery factories, the speed and output of the product manuals introduced in the two sides' pactions are not available when meeting the requirements of high production and high speed and cost reduction in the use of factories. It is not available to satisfy the production quality and conditions at all times, but to achieve the highest speed in the experiment as a long-term index of sales promotion and even exaggerate some functions.

I have consulted Swiss Lida Company: "can the comber produced by your company known as 450 times per minute achieve the design targets in the actual production process? How long is its life and stability?" Lida professionals replied that the work was basically ineffective and that the quality of production was guaranteed only when the job was embedded.

The author has used the machine for many years in Jiangsu Huaxi textile mill to prove that this product is of the highest quality in China.

In fact, the reputation and reputation of Lida textile machinery in the Chinese market is obvious to all.

Of course,

cotton spinning

The factory also gradually found out that the production speed should be considered at least 20% of the water space.

New products are not standardized to the market.

It is understood that the new equipment exhibited at the European textile machinery exhibition will be put on the market only after testing at least 2 years or so.

Some domestic spinning machines in Wuxi Mashan textile machine experiment factory also carry out similar factories that have scale and simulated cotton spinning and operation.

At present, many cotton mills reflect the fact that there are still many textile mills that directly or indirectly regard the cotton mills as an experimental factory. There is no cooperation agreement between the production equipment and the equipment. The spinning machine factory often sells the newly designed equipment which has not been tested practically below the market price, but finally pfers the risk to the plant, which consumes a lot of manpower and material resources, and the quality is not guaranteed.

There is no good market environment and notarial institution for protecting the rights and interests of cotton spinning enterprises in China.

voice

"My company has a self levelling drawing machine output detection bell mouth, less than 100 grams of weight, the price is about 20 thousand yuan.

The most used solenoid valve, as long as a change of a seal ring, up to ten or twenty yuan, but no substitute, had to spend 1000 yuan to buy a solenoid valve.

The encoder is less than a few thousand yuan, more than 10000 yuan, and life expectancy is not as long as imagined.

Similarly, the spring and bearing seal traps equipped with automatic winding splicer can only be used for 3 months or so, which is much lower than that of over one year abroad. The quality of foreign parts is stable, but the price should be at least 3 times.

The problem is that there are a large number of counterfeit and shoddy products in domestic parts and equipment, which cause unforeseen adverse consequences through abnormal channels, resulting in waste of people, money and goods.

People in the industry talk about it. The whole machine and the prototype of the spinning machine factory can do well, but they do not want to work hard on a part of the machine. Even a key screw is not good enough to import.

Because I have been in the production line for a long time, it may not be pleasant to speak.

The biggest headache for the maintenance worker is that imported equipment is replaced by domestic bearings, basically short life, and advanced equipment can only be useless.

Sometimes I really want to express my feelings, why the spaceship is all in the sky, but not even a bearing! "