Home >

Analysis Of Relationship Between Shoe Template And Inner Template

2011/1/1 16:39:00 79

??? 日本語 Fran?ais English 中文

The inner model is made up of the front and rear parts, and then extends from the front to the inside and the front of the back.

Shoes tongue

Inside, before reinforcement...

And so on:

Antiskid Lane

Mouth, roll mouth, shoe eyes,

eyelet

Reinforcement...

And so on.

The shoes must be stable, and the unstable shoes will be judged to be bad products. The instability of the floor is caused by three factors. First, the design is improper; second, improper assembly; third, improper production.

Examples of improper design are usually

A shoe last

Side line error or

Sole

The side line error and the last side line and bottom side line are correct, but they can not cooperate with each other. The ground error is caused by the bottom matching: an example of improper assembly is that the side line is not considered when applying the relevant filling material.

standard

Degree,

standard

The side line and bottom side line of the last line are changed due to the incorrect filling material. The improper example is due to improper placement of the bottom into the last, extrusion or skewness), improper bottom pressing (poor bottom die or pressure base) and the wrong angle of the nail.

The bottom, the makeup and the iron core constitute the three in one.

Material Science

The three in one bottom is designed to stabilize the side line of the shoe, so that the radian of the rear part of the shoe will not change due to the load.

Therefore, the side line is changed. Therefore, the design of the three in one bottom must be consistent with the side line radii formed by the midsole, so that the three in one middle -e_..4a, l line has the accurate radian of the upper (last side line) and the bottom (bottom side line); the three in one bottom structure must also be solid without peeling, and the structure of the middle sole is different from that of the shoe, such as the pad.

Insole

The structure of the shoe can be made into a middle sole with one piece of makeup (exposed to the iron core): the rear movable middle sole (3m/m thickness).

Insole

The shoes with the needs of the outsole can be made into a single center of iron core.

standard

The last side line matches the middle bottom of the last side line and matches the bottom platform of the bottom side line.

Forming

The three essential designs of the shoes are smooth. The wrong design of any project is the cause of the instability of the shoes.

The inner template is salted according to the shoe template, so there is an accurate shoe pattern, so that there can be an accurate inner template. When trying to help, it is often found that many of the shoe models will not last. In fact, a large percentage is made from the inner model, inaccurately or internally.

Material Science

No, or the internal structure design is not good.

The inner model is mostly made up of the front and rear parts, and then extends from the front to the inside because of the demand for wear and the joint structure.

And so on: extended from behind: anti slip, reverse mouth, roll mouth wrap, shoes eyes, shoes eye reinforcement...

And so on.

The main structure is the combination of the front and rear parts. When making the inner template, the inner and outer sides of the upper and inner parts must be noticed, and the inner lining should be included.

Material Science

Shoe upper

Material Science

The extension rate is poor.

Material Science

Try to choose shoes.

Material Science

The rate of elongation is greater than that of shoe upper.

Material Science

Good plasticity, which can be avoided.

Forming

When produced by internal factors, creating a shoe upper

Forming

The negative burden.

The inner template is taken from the shoe pattern, and the inner template and the shoe pattern have the relationship between the inside and outside. The vamp is the peripheral role. The inner template must be the role of the inner part. Therefore, it is necessary to understand and make the difference of the width of the inner and outer girth when taking the inner template. Generally, the thickness of the leather can be used as the gap between the inner and outer sides, such as the thickness of the fabric using 2.0m/m thickness.

Half panel

When the shoe width is 300m/m (100m/m), the inner template should be set to 298m/m (or 98m/m).

Material Science

In general, most of the former are thinner and softer cloth.

Material Science

When applied, the front template can be added or reduced according to the difference of the inner and outer girth depending on the material and working mode.

Generally used last.

Forming

(last set) method

Forming

Shoes, vamp and inside are pre assembled in a closed way. First, the hard liner is put into place, so that the hard lining is sealed between the surface and the inside. At this time, it is advisable to use the hot melt adhesive with hot melt characteristics.