Design Of Asymmetrical Women'S Shoes In Front Of Broken Door

The asymmetrical structure of the front door is a kind of asymmetric structure which is overlapped by the inside and outside parts of the door.

The change of this structure is directly related to saving materials, because the width of women's shallow shoe door is generally narrowed, so that the problem of scratch becomes a problem.

If we break the whole door and form the two part of independence, we can save a lot of materials when we draw it.

When designing the asymmetric structure of fractographic door, we need to draw the outline of the half panel, and carry out the design of outer Huai and Li Huai, respectively.

When drawing the drawing, draw the outer half panel, then draw the outline of the half panel by J, V and Q.

The contour of the half face is also depicted with the outer half panel, but the line of the mouth should be made.

Using J, Vo and Q to control half panel graphics, three points can be reduced.

The design of L.'s inlaid shoes

As shown in Fig. 3-5-7, the complete door is broken, and the upper is divided into two parts: the inside and outside helps.

A decorative strip is arranged on the shoe mouth of Li Huai, and it reaches the bottom of the outer palm directly after passing through the shoe mouth.

When drawing the structural design, draw the outline of the outer side of the outer side, then connect the back midline.

We use J, Vo and Q'points to control the points, and draw the outline of the half panel, and make the outline of the mouth.

As a result, a shoe upper tile is laid out, and all kinds of parts inside and outside are designed on the tile map.

First design the Huai line of Li Huai, go through the mouth door and point directly to the bottom of the outside, then design an equal width decorative strip along the shoe.

Then we design the shoe line of the outer arms, and the shoe line of the inside and outside is intersected at the position of the back midline to form a straight door structure.

Other designs with round shoes!

The Huai Huai's back group increased by a 1/2A volume, and the outer side of the Huai group reduced a 1/2A volume, and the waist waist was constantly helping, but there were craft handles.

When you make a template, you follow the directions.

Design of 2. Bow Shoes

As shown in Fig. 3-5-8, the front part of the shoe has a bow shaped part extending from the inside of the shoe through the mouth door and reaching the heel part along the outer shoe.

The structure of the shoe is similar to that of the Striped shoes. The upper is made up of three parts, the bow shaped part of which can be highlighted by differential leather.

In the structural design, we should also draw the outline of the half panels of the Huai and outer Huai, first design the contour line of the outer shoe, then design the bowed bow parts, then design the shoe contour.

Finally, finish the other design.

The design of 3. mid seam shoes

As shown in Fig. 3-5-9, the front midline of the shoe is broken, while the broken line extends backward, while the outer side of the shoe is inclined to the outer side, until the heel arc is formed, and the hollow back structure is used, the shoe line is extended and intersected with the open middle stitch.

There are two pairs of flowers echoing each other on the break line of the shoe and the heel.

The methods of drawing structural diagrams are basically the same.

Design of 4. sharp corner decorative shoes

As shown in figure 3-5-10, the upper side of the shoe upper is overlapped on the front side of the outer garment in a sharp corner, which is the imitation design of the color picture L-17.

There are metal decorations on the front and back sides of the shoes, which are four pieces of buttons and the next ones respectively.

Note that there is a break position between the outer arms and the trim parts.

When drawing the structural design plan, make the tiling map, first design the shoe line with the side of the shoe side, and connect the sharp corner component, design the location of the false line and the decoration part, then design the shoe line of the outer shoe, and so on, which is the same as the previous design method.

Because the heel is higher, the shoe's stilts become larger, and there is a overlap phenomenon between the inside and outside of the tile on the tile map. Because of the split design, the inside and outside arms are disconnected, which will not affect the design effect and the template.

Through the design of the above shoes, we can see that the design of the female shoes with asymmetric structure is the same as that of the symmetrical structure, and only the asymmetric parts are designed separately.

When the asymmetric parts do not affect the opening of the shallow shoe, it can be basically designed according to the symmetrical structure. If the door is damaged, the "tile map" method should be adopted instead of the design.